v2 instr, modele kartonowe, V2 [ Pobierz całość w formacie PDF ]
Assembly Instructions for V-2 Rocket
History
In the 1930s the German army began research into long range rockets. Working at Peenemünde on the Baltic coast,
Wernher von Braun and his team developed a series of liquid-fuelled designs, culminating in the A-4. This revolutionary
rocket, standing over 46 feet tall, first flew successfully on 3 October, 1942. It was fuelled by methyl alcohol and liquid
oxygen, and featured a gyroscopic guidance system. Armed with a 2,000 lb explosive warhead, the A-4 was renamed for
propaganda purposes V-2 (V standing for
Vergeltungswaffe
, or vengeance weapon). By the end of the Second World War
over 5,000 had been built, most being fired at the cities of London and Antwerp. The high speed of the V-2 made them
immune to interception. Although they caused great destruction and loss of life, their guidance system was too inaccurate
to hit any target smaller than a city, and their military effect was small in proportion to the resources employed in their
manufacture. In spite of these shortcomings, the American and Soviet governments showed great interest in the V-2, and
both countries recruited German rocket scientists after the end of the war. The V-2 is a direct ancestor of the Scud missile
employed in the Gulf War, and of the giant Saturn V rocket that sent the first humans to the moon.
The Model
This model builds into an accurate and detailed 1/32 scale replica that stands over 17 inches tall. A word of caution: this is not suitable for
assembly by young children, due to the use of sharp tools and the complexity of some assembly steps. It is recommended for those with
some previous experience in card modeling. If you have any comments or suggestions regarding this kit, I can be reached by e-mail at
models@currell.net
This document contains the instructions only. Model parts are contained in a separate document. Print out the part sheets on 8.5"x11" or
A4 size white card stock suitable to your printer. Sheet
G
contains structural formers, and may if desired be printed on heavier stock.
Alternately, extra parts are provided on sheet
G
to allow you to “double up” the formers.
Tools
Before beginning, you will need the following tools and materials:
a) white glue
b) a glue applicator such as wooden toothpicks or a small paintbrush
c) scissors
d) a sharp knife for cutting
e) a flat cutting surface
f) a ruler or straight edge
g) a scoring tool or blunt knife for creasing the fold lines.
Hints
a) Select a well-lit, comfortable work area that will remain undisturbed when you are not there.
b) Keep your hands and tools clean when working, to avoid getting glue on visible parts of the model.
c) It’s easier to stay organized if you only cut out those parts you need for each step.
d) Make sure your knife is sharp. When cutting straight lines, use a straight-edge. Scissors, if used carefully, can be used for large
curved parts.
e) Study the diagrams carefully, and always test-fit the parts before applying glue.
f) You may wish to colour the edges of the parts to make seams less visible. Pencil crayon or paint applied with a fine brush can be
used (experiment on scrap pieces to see what works best).
Assembly
These instructions apply to both the colour (camouflaged) and black & white versions of the model. Directional terms such as “top” and
“bottom” assume the rocket is vertical (fins at bottom). Scoring of parts is usually indicated by thin black lines outside the part’s outline.
Score parts
before
cutting them out. In the diagrams, subassemblies are identified by a number within a circle (e.g. ), corresponding to
the step number in which it was assembled.
Assemble the body sections (
steps 1–4
). The body of the rocket is made up of seven assemblies. These assemblies comprise an outer
surface segment (the “skin” of the rocket), a connecting strip and (except for the nose cone) a circular former to provide strength and
maintain the segment’s shape. To construct a typical assembly, carefully cut out the parts and glue the connecting strip to the inside of the
surface segment. These strips have a thin line along the centre, which must be lined up with the respective edges of the surface segment
(see the diagrams). The segment is then rolled so the edges butt together and are held by the connecting strip. Once dry, the former ring is
V2_instr.pdf v1.3 September 2000 © Ralph Currell
Page 1 of 4
glued inside the assembly, as close to the narrow end as necessary to obtain a snug fit.
Assemble the exhaust cone (
step 5
). Remember that the gray printed side of the exhaust cone will be on the inside.
Join the nose sections (
step 6
) and the tail sections (
step 7
) ensuring the vertical seams line up. All remaining parts will be attached to the
tail, so the nose can be set aside until later.
There are four fins. The fin shape is somewhat complicated, so study the drawings carefully and dry-fit the parts before applying glue.
When cutting out the fins, ensure that the centre-line is scored for folding, and that the two narrow slots at the bottom (separating the
rudder from the fin body) are cut. Each fin requires an interior supporting structure (
step 8
), which is made up of four struts folded and
glued in accordance with the template on parts sheet
A
. This structure is glued into one side of the fin, and the other side is folded over
(
step 9
). The leading and outside edges of the fin, the rudder, and the angled bottom edge are then glued together to form a sharp edge.
Attach the fins to the tail assembly, gluing to the lightly shaded areas on the side of the body (
step 10
). If building the black and white
version, the orientation of each fin is determined by its markings. Proper alignment is crucial to the appearance of the final model! Ensure
that the fins are exactly 90 degrees apart, and that the base of the fin, where it meets the body, is flush with the body’s base plate. Also
verify that the bottom of the fins are all at the same level (all four fins should rest on a flat surface with no wobble). Attach the exhaust
cone, taking care that it is centred, and that the tabs on the bottom line up with the fins.
Assemble the servo motor housings (
step 11
). When cutting out the end plate E9, it will be easier if the hole is opened before the outside
edges are cut. Note that the side plates A2-A9 are numbered; both sides of each housing must have the same number. Assemble the exhaust
vanes (
steps 12–14
).
Glue the servo housings from step 11 to the fins, ensuring the numbers correspond to the fin number (
step 15
). Assemble the antennae E10
and the chain drive covers E8 (
step 16
).
Attach the fairing panels A10-A17 such that they form a smooth arc between the fins and the body (
step 17
). The curve at the base of these
panels should match the curve of the housings directly beneath them. Thin lines on the side of the fin and the body indicate where the edges
of the fairings line up. Attach the antennae to the bottom of the fins, and the chain drive covers (narrow end up) to each side of the fins.
Form the connector covers D3–D5 and attach to the body sides. Attach the exhaust vanes to the holes in the drive housings, leaving 0.05"
(1.4 mm) of the drive shaft exposed.
Finally, glue the nose section to the tail (
step 18
), ensuring the body seams line up.
1
2
Nose
cone
Body
segments
B1
F1
G1a
G1
A1
F4
3
Centre
segment
B2
F3
G3,G3a
V2_instr.pdf v1.3 September 2000 © Ralph Currell
Page 2 of 4
 4
D2
G6
5
C4
Base
segment
Exhaust
cone
Inked surface
faces down
Inked surface
faces inside
C2
D2 should be flush
with base of segment
C3
D6
Inked surface
faces down
C5
F5
Line up F5
with this edge
6
1
2
G2,G2a
3
8
F2
C6
Use template
on parts sheet A
to align parts
correctly.
Fin
structure
(4 pieces)
Inked surface
faces outward
Nose
assembly
Assemble as
shown in step 2
E2
E4
7
G5,G5a
G4,G4a
4
F6
D7
F7
D8
B3
E3
Tail
assembly
Assemble as
shown in step 2
9
10
Black & white version:
arrange fin colours as shown
Fin
assembly
(4 pieces)
Fin
placement
7
white
black
(body seam
here)
C1
C7
D1
E1
white
black
white
black
white
black
Bottom view
7
Black & white version:
ensure ink pattern on strut
matches fin colours.
Glue fin edges
together in
places shown
9
9
9
9
Cut notches on
fins before assembly
5
V2_instr.pdf v1.3 September 2000 © Ralph Currell
Page 3 of 4
11
Servo motor
housing
(4 pieces)
A3
A5
A7
A9
A2
A4
A6
A8
12
Vane base
(4 pieces)
13
Vane
parts
(4 of each)
E8
E9
E6
Parts A2-A9 have
numbers printed on them.
Left and right sides of
each assembly must
have same number.
E7
E11
Parts E8, E11
fold over and glue,
then cut out shape
14
Vane
assembly
(4 pieces)
15
Bottom view
16
Antennae &
chain drive
covers
Servo
housing
placement
This number
matches
fin number
Fin 1
(body seam)
E5
8 pieces
E12
E8
Fin 4
Fin 2
E13
10
10
E11
13
Fin 3
E10
4 pieces
17
Fin 2
Fin 4
Fairings &
miscellaneous
parts
Fin 1
(body seam)
Fin 3
Fin 3
Fin 1
(body seam)
A10
A13
A17
A14
Fairings (parts
A10-A17) curve
to match shape of
servo housing
assembly
A11
A12
A16
A15
D3
D5
D3
D4
E8
2 per fin
(Black & white version:
match colour of E8
to fin colour)
14
1 per fin
0.05 in
1.4 mm
E10
1 per fin
18
6
17
Final
assembly
V2_instr.pdf v1.3 September 2000 © Ralph Currell
Page 4 of 4
[ Pobierz całość w formacie PDF ]